Discovering Plumbing Basics is Crucial When Installing a Bathtub
Discovering Plumbing Basics is Crucial When Installing a Bathtub
Blog Article
We've found the article relating to Installing A Bathtub listed below on the web and figured it made good sense to discuss it with you on my blog.
Installing a bath tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough job. If the old tub is readily obtainable, the job can relocate speedily; if you need to open a wall surface to eliminate the old bathtub and place the brand-new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually certified yourself for the work and are comfortable trying it. Rather than hiring a professional to take control of a halfway-completed task, it is far better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This article will aid you mount a brand-new tub in your bathroom if you have already purchased a new tub and do not require to change the plan of your previous water system pipelines.
Your devices as well as material checklist ought to comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing taps can be quite troublesome because of the limited gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place in between the tap and the sink. Secure the faucet in position with the supplier supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal tap ports. The former kind should be attached to the tap finishes first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Tub
Using both wood boards under its feet, place the bathtub in the needed placement. The wood boards are useful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest versatile tap connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and inspect all joints and new pipework for leakages and tighten them if essential. Load the tub as well as likewise inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been used at least once as this will certainly settle it right into its last placement.
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom should be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent strain on the tub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to permeate the wall between the bath and the tiling, resulting in complications with moisture as well as possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can split relatively very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the market. It is advisable to fit the floor tiles using water-resistant or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that excerpt was worth the trouble. Sharing is nice. Helping people is fun. We truly appreciate reading our article about How to Install a Bathtub.
Quick relief? Dial! Report this page